BOG 回收机组（卸车小霸王）BOG recovery unit
卸车结束把槽车余压抽干净：闪蒸 BOG 经回热、压缩后回储罐或送管网，一台机组把卸车与回收两件事做完。Pulls the last pressure out of the trailer: flash BOG is reheated, compressed and returned to the tank or the network — unloading and recovery in one package.
产品概述Product overview
槽车卸完还留 1–3 公斤压力，这部分 BOG 以往直接放空。按 0.1 MPa 余压折算约 80 kg LNG，3 公斤余压折 200 多千克液相、合 348 方气态天然气；三天一卸的站，一年放掉的量就抵得上一台机组。Trailers arrive with 1–3 bar left: at 0.1 MPa that is about 80 kg of LNG, at 3 bar over 200 kg liquid, roughly 348 m³ of gas — vented, it is the price of the unit every year.
两个模式走一套管路：卸车时槽车 BOG 经回热器升温，压缩后进储罐；回收时储罐蒸发气经回热、压缩回到槽车或管网。进口往复式压缩机、回热器、空冷器与油气分离集成在一个箱体内，接管接线即可投用。Two modes, one piping set: during unloading the trailer BOG is reheated, compressed and pushed into the tank; during recovery the tank boil-off goes back to the trailer or the network.
防爆电控箱就地显示进出口压力与温度；排气温度过高、线圈温度过高、入口温度过低自动保护，油位过高、油位过低、油位异常与润滑油压异常各自停机，不靠人盯表。An Ex panel shows inlet and outlet pressure and temperature; discharge, coil and low-inlet temperature are protected, with separate trips for oil level and oil pressure.
结构组成What is in the cabinet
核心优势Why this design
- 卸得干净：余压抽到 1 公斤以下，槽车不带压返厂。Clean unloading: pressure pulled below 1 bar before the trailer leaves.
- 回收见钱：放掉的 BOG 变成能计量、能结算的气。Recovered value: vented BOG becomes metered, billable gas.
- 保护齐备：温度三道、润滑四项，异常自动停机。Protection first: three temperature and four lubricant trips.
- 成柜即装：落地接管接线，不占现场工期。Cabinet-ready: land it, connect it, run it.
四件做到位，设备才站得稳Four things done right
调压器、切断阀、过滤器按工况选型，出厂做全性能测试，压力稳得住。
管路、阀组与仪表厂内一次组对、试压，现场接上进出口就能投用。
超压切断与放散、温度与浓度监控、自动运行，异常先切后报。
每台带检验试验状态标识、检验记录与检验报告，跟设备一起交到现场。
产品实拍Product photos
BOG 回收机组 · 现场对接与内装BOG recovery unit — hook-up and internals 点击图片放大查看。 Click to enlarge.
技术参数Technical data
| 型号Model | LC-SY-100-1-C（卸车小霸王）LC-SY-100-1-C |
|---|---|
| 适用介质Medium | 天然气（BOG / 低温闪蒸蒸气）Natural gas (BOG / flash vapour) |
| 最大工作压力Max pressure | 0.8 MPa（可至 1.6 MPa）0.8 MPa (1.6 MPa option) |
| 排气量Capacity | 100 m³/h（系列 100–500 m³/h）100 m³/h (series 100–500 m³/h) |
| 整机功率Installed power | 22 kW22 kW |
| 转速Speed | 1450 RPM1450 RPM |
| 工作电源Power supply | AC 380 V ±10%，50 Hz ±1 HzAC 380 V ±10%, 50 Hz ±1 Hz |
| 工作环境Ambient | −40~60 ℃，相对湿度 ≤90%−40 to 60 °C, RH ≤ 90% |
| 外形尺寸Dimensions | 1600 × 1200 × 1600 mm1600 × 1200 × 1600 mm |
| 整机重量Weight | 650 kg650 kg |
以上为该系列出厂数据；排气量与压力等级按站点卸车频次、储罐容积与槽车余压选定，一台机组只做一个规格，参数以合同技术文件为准。Data is for this series; capacity and pressure class are selected on unloading frequency, tank volume and trailer residual pressure.
适用工况Typical duties
适合什么工况，什么情况不适用Where it fits, and where it does not
这套设备适合Best for
- 卸车频次高的 LNG 站，余压放空的量能直接折成气费LNG stations unloading often, where vented residual pressure is real money
- 槽车返厂仍带 1 公斤以上余压、装货方要求泄压Trailers leaving with over 1 bar, where the loader requires depressurising
- 储罐蒸发气长期外排、站内需要回罐或回网Tanks venting boil-off that should go back to storage or the network
- 场地与工期紧，需要成柜落地、接管接线即用Tight site and schedule, needing a cabinet that runs on hook-up
需要提前确认的边界Check before ordering
- 回收是否经济要按卸车次数与液量算，次数太少不划算Economics depend on unloading frequency and litres per load
- 进出口接口需与槽车、储罐一致，转换接头要提前确认Couplings must match trailer and tank; adaptors confirmed in advance
- 现场需划分防爆区域并保证通风与电源容量Hazardous area classification, ventilation and power capacity required
标准配置Standard configuration
以上为常规配置，实际随机组按工况与用户管网条件确定，可按需增减。Standard scope shown; final scope is set by duty and network conditions, and can be adjusted.
主要零部件Main components
零部件的品牌与型号按项目技术要求与用户指定品牌确定，页内不限定具体厂家。Brand and model are fixed by project specification and the user's approved vendor list.
同类设备Related equipment
把你的卸车频次与储罐容积发过来，我们算回收量Send the unloading frequency and tank volume, we size the recovery rate
需要提供：介质与储罐容积、单次卸车液量、槽车余压、卸车间隔、现场电源与防爆区域划分。We need medium, tank volume, litres per load, residual pressure, unloading interval and site power.