高压氢，不漏不超压High-pressure hydrogen, sealed and protected
氢气成套设备：三级减压、专用密封与超压联锁，把管束车氢气安全降到用氢点的压力。Hydrogen package: three-stage reduction, dedicated sealing and over-pressure interlock.
产品概述Product overview
氢气与天然气的差别，在撬上会变成三个具体问题：一是密度极低，同样压差下的流速和噪音都更极端；二是分子小，对阀杆填料与法兰密封的泄漏率要求高一个量级；三是高压下会渗入钢材造成氢脆，材料与焊接工艺必须另作评定。所以氢撬不套用天然气撬的图纸，而是按三级减压把压比进一步拆小，密封面改金属硬密封，出厂做氦检漏。Low density, small molecules and embrittlement force three-stage reduction, metal seals and helium leak testing.
氢用管道新国标发布后，选型还要对上管道材料、焊评与检验比例的要求。这类项目泰燃按介质、压力、纯度三项先定材料，再定阀组，最后定控制逻辑。New hydrogen piping standards add material, weld procedure and inspection requirements.
工作原理：氢气为什么更难伺候Working principle: why hydrogen is harder to handle
氢气分子最小、扩散系数最高，也最容易从密封面、螺纹与法兰间隙里“钻”出去。同样一个接头，天然气不漏，氢气就可能微漏并积聚。所以氢系统的第一原则不是“能不能承压”，而是“能不能密封并让泄漏可被发现”。Hydrogen has the smallest molecule and the highest diffusion coefficient. It escapes through seals, threads and flange gaps that hold natural gas perfectly. The first principle in hydrogen service is therefore not pressure capability but sealing plus detectable leakage.
第二是材料。高压氢会让部分钢材发生氢脆——延性与断裂韧性下降，尤其在焊接热影响区与高应力部位。选材要做相容性评估，焊接工艺要有评定，硬度也要控制。常规碳钢在高压氢环境里不能随手照搬。The second is materials. High-pressure hydrogen embrittles some steels, cutting ductility and fracture toughness, most of all in weld heat-affected zones and at high stress. Material compatibility must be assessed, welding procedures qualified, and hardness controlled. Plain carbon steel cannot simply be carried over.
第三是安全设计。氢气爆炸极限极宽（约 4%–75%），无色无味，泄漏不易被察觉。撬上要配可燃气体探测、紧急切断、放散与接地；管路的流速也要控制，避免静电积聚。The third is safety design. Hydrogen's flammable range is very wide (roughly 4–75 %), it is colourless and odourless, and leaks go unnoticed. Skids carry gas detection, emergency shut-off, venting and earthing, and flow velocity is limited to avoid static build-up.
结构组成What is on the skid
核心优势Why this design
- 三级减压：单级压比小，出口压力稳、阀口寿命长。Three stages keep outlet stable.
- 低泄漏：金属硬密封，出厂氦检漏。Metal seals with helium testing.
- 材料适配：按氢脆风险选材并做焊评。Materials and WPS for hydrogen service.
- 安全联锁：氢探测与切断联动。Detection linked to shut-off.
四件做到位，设备才站得稳Four things done right
调压器、切断阀、过滤器按工况选型，出厂做全性能测试，压力稳得住。
管路、阀组与仪表厂内一次组对、试压，现场接上进出口就能投用。
超压切断与放散、温度与浓度监控、自动运行，异常先切后报。
每台带检验试验状态标识、检验记录与检验报告，跟设备一起交到现场。
产品实拍Product photos
氢气减压撬 · 高压段Hydrogen reducing skid — high-pressure stage 点击图片放大查看。 Click to enlarge.
技术参数Technical data
| 介质Medium | 氢气 / 掺氢天然气Hydrogen / H₂-blended gas |
|---|---|
| 减压级数Stages | 3 级3 |
| 进口压力Inlet | 按气源确定（管束车/管道）Per source |
| 出口压力Outlet | 按用户工艺设定Per process |
| 密封Sealing | 金属硬密封，低泄漏等级Metal seat, low leakage |
| 检验Testing | 强度、气密、氦检漏Strength, leak, helium |
| 联锁Interlock | 超压切断 + 氢探测Slam-shut + H₂ detection |
表中为该系列典型配置。项目流量、介质与进出口压力不同时按工况单独设计，参数以合同技术文件为准。Typical configuration; units are engineered per duty and the contract data sheet governs.
选型与计算要点Selection points
适用工况Typical duties
适合什么工况，什么情况不适用Where it fits, and where it does not
这套设备适合Best for
- 高压气源一次减到用压，撬装交付High-pressure source reduced to use pressure on one skid
- 配泄漏监测与联锁，安全措施成套Leak detection and interlocks included
- 金属密封阀件，减少渗透泄漏Metal-seated valves limit permeation
- 可按防爆区域配置电气与仪表Electricals and instruments matched to the hazardous area
需要提前确认的边界Check before ordering
- 氢脆与渗透要求专用材质，不能按天然气管路代用Hydrogen embrittlement and permeation need dedicated materials
- 需划分防爆区域并保证通风Hazardous area classification and ventilation required
- 检测仪表需定期校准Detectors need periodic calibration
标准配置Standard configuration
以上为常规配置，实际随机组按工况与用户管网条件确定，可按需增减。Standard scope shown; final scope is set by duty and network conditions, and can be adjusted.
主要零部件Main components
零部件的品牌与型号按项目技术要求与用户指定品牌确定，页内不限定具体厂家。Brand and model are fixed by project specification and the user's approved vendor list.
常见问题FAQ
氢气撬能用在天然气上吗？Can a hydrogen skid handle natural gas?
结构上可以，但选型与检验要求不同，反过来更不行——天然气的设备未经相容性评估不能直接用于氢气。Structurally yes, but selection and testing differ; the reverse is not acceptable — gas-rated equipment cannot go into hydrogen service without a compatibility assessment.
怎么判断有没有微漏？How is a small leak found?
用便携式氢气探测器巡检、对接头做肥皂液或氦检漏；固定式探测器要定期标定，不能只靠报警灯。Portable detectors on patrol, soap solution or helium testing at joints, and regularly calibrated fixed detectors — not just the alarm lamp.
氢气管道为什么不能用普通碳钢？Why not plain carbon steel?
高压氢会引起氢脆，降低韧性与疲劳寿命，焊缝与高应力区尤其敏感。具体可用性要按压力、纯度与标准评估。High-pressure hydrogen embrittles steel, reducing toughness and fatigue life, especially in welds and high-stress areas. Suitability is assessed by pressure, purity and the applicable code.
放散管有什么要求？What do vent stacks need?
朝向安全、高度足够、设阻火器与防雷接地，排放不能朝向人员区或进气口。A safe direction, adequate height, a flame arrester and lightning earthing, never discharging at people or air intakes.
验收要看哪些资料？What paperwork is expected?
材质证明与相容性评估、焊接工艺评定、强度与气密（含氦检漏）报告、探测器标定记录、接地电阻实测记录。Material certificates and compatibility assessment, welding procedure qualification, strength and tightness reports including helium testing, detector calibration records and measured earthing resistance.
同类设备Related equipment
把你的工况发过来，我们出选型表Send your duty, we return a selection sheet
需要提供：介质、最大/最小流量、进口压力、出口压力、现场热源（电/热水/蒸汽）、安装场地条件。We need medium, min/max flow, inlet and outlet pressure, available heat source and site conditions.